Our doorways said nothing.
Not even hello. Or goodbye.
We wanted them to say something, anything really.
So when changing out the trim in our home, we decided
the doorways also needed a little change.
The doorways in our home were sheet rock only.
No pretty wood.
No pretty molding.
Nothing that spoke of originality.
They were painted, and that was about it.
The doorways in our home were sheet rock only.
No pretty wood.
No pretty molding.
Nothing that spoke of originality.
They were painted, and that was about it.
To bring more character into our house,
we added big molding around the doors.
What we used:
4 - 1x4x7 MDF
2 - 1x4x5 MDF
2 - 1x6x7 MDF
4 - 1x2x5 Primed Pine
Nails
Tools you need:
Miter Saw (or chop saw)
Tape Measure
Pencils - preferably a dozen; you'll use one,
set it down, forget where you put it,
look for another one, use it, set that one down,
forget there is one behind your ear,
forget one near the saw,
forget the one by the door,
...you are starting to get the idea.
First we measured the top of the inside of the doorway.
I then cut a 1x6 to fit the top.
Once the top was nalied in place, I measured
and cut 1x6s for the sides of the door frame.
The outside frame of the door was framed with 1x4.
Each piece was measured even with the top height of the 1x6.
Confusing right?
I circled below what I mean.
Each piece was measured even with the top height of the 1x6.
Confusing right?
I circled below what I mean.
The top of the door way was framed by a 1x4 and 2 - 1x2s.
The 1x4 is cut to align with the far side of the
The 1x4 is cut to align with the far side of the
1x4s framing the sides of the doorway.
Each 1x2 is 1 inch longer than the 1x4 on both sides.
The bottom 1x2 is nailed into place,
The bottom 1x2 is nailed into place,
followed with the 1x4 and capped with the last 1x2.
Each lining up with the other.
Here is a visual to give you an idea of what was done.
My next steps were filling in the nail holes and using caulk to fill in the gaps.
Caulk is a miracle worker and covers a multitude of imperfections.
Caulk will not, however, cover up the imperfection
of dirty clothes you notice your kids are wearing
as you head out the door to go to church.
Caulk can't do that.
The final step is one last coat of paint.
TA DA!
A touch of character to a previously boring doorway!
Seeing them side by side shows what a big difference a little trim can do
to the look of a room.
Wow.
That makes such a huge difference. Fabulous job!!
ReplyDeleteThank you Roxanne! Confession : sometimes I just stop and stare at them. :)
DeleteFAB-U-LOUS!!! Really! This is such a GREAT idea! I really like how it reminds me of those big old houses that always have that big beautiful woodwork. Great job!
ReplyDeleteThank you so much Winter! We wanted something that said "character" and you have just confirmed to me we got it right. :) Thank you!
Delete3 years later and I love this. Easy for those of us (aka me)who don't wan to mess with fancy angle cuts and such. Thank you for getting linked to Pinterest.
ReplyDeleteThank you! I still stare at them with love sometimes! :)
DeleteWow how much of a difference😍
ReplyDeleteThank you Ericka!
DeleteWhere did u buy or order the pieces thanks
ReplyDeleteHi! I got these pieces from a local lumber yard. Any lumber yard should carry these, including the big national ones.
DeleteOlder post, I know, but we are getting ready to frame a door, so I discovered your post. VERY NICE!! What a dramatic difference! Thanks for sharing.
ReplyDeleteThank you! We absolutely love them!
DeleteDid you do both sides?
ReplyDeleteYes we did.
DeleteDid you have to rip the 1x6 down since the wall thickness is only 4 3/4" wide? (I'm assuming 2x4 plus 1/2" drywall on either side?
ReplyDeleteHi Joe,
DeleteI did not have to rip the 1x6 down. The way the 1x4 boards butt up against the 1x6 boards allowed it so that I did not have to rip the 1x6 down.
Thanks! Just did this to two doors this weekend
ReplyDeleteFantastic!!! This makes me so happy. Would love to see them when you're finished!
ReplyDeleteWhat did you use for baseboard in the room shown???
ReplyDeleteHi Matthew, we used 6" baseboards.
DeleteHow did you prepare the raw edge/edges of the 1/2?
ReplyDeleteHi Deanna,
DeleteI painted them with a couple coats of paint.
I love this plan on doing this to my kitchen to main living room also. My question is with the flooring tho. It looks like you cut it to the today on each side how did you fill that in? Did you just cut a piece horizontal to fit?We have done that, cut to the doorway, and don't know the best route to make it look finished.
ReplyDeleteHi, as it looks like your phone did an auto-correct, I'm not 100% sure I know the question you are asking. We had laid our floors down before doing the trim. The flooring went 1/4" to the wall. When we did the trim, the width of the board covered the empty space between the flooring and the wall. The piece running the width of the door is a transitional piece we ordered with our flooring. We cut that to butt up against both sides of the door covering any exposed areas.
DeleteFantastic job! L-O-V-E it. Hope to follow your example soon. Thanks for sharing. :-)
ReplyDeleteHello. We are in middle of doing our door trim and already have some down hallway done. Do you not feel the top sticks out to far? With several doors in a row I’m not sure I like the look.
ReplyDeleteThat is the one the greatest things about doing home renovations yourself - you can do whatever your heart desires! I love the look as it works well in my home and layout. If you want the overhang to be smaller you can easily do that too!
DeleteThank you for great idea and making it beautiful stylish and easy, we are using your template right now. So far looks fantastic.
ReplyDelete